ARDEX

ARDEX G6 FLEX 1-6

Flex- joint compound


Cement-base

For joint widths of 1-6 mm


For indoor and outdoor application


Flexible,

long processibility,

Water and dirt repellent,

highest strength.

Quartz-free - Very fine and smooth joint surface.

very good flank adhesion.

With preventive protection against mold fungi.

Suitable for floors and walls with integrated heating elements.


application

For jointing:
 

•     Ceramic tiles
•     glass tiles
•     Natural and concrete block boards (moisture-insensitive)
•     Mosaics of glass, porcelain and ceramics

Material application rate:

with joint width 3 mm, joint depth 5 mm for tiles or medium mosaic
of 60 x 60 cm is about 0.10 kg / m²
of 30 x 60 cm approximately 0.15 kg m²
of 30 x 30 cm is about 0.20 kg / m²
of 15 x 15 cm is about 0.35 kg / m²
of 10 x 10 cm is about 0.45 kg / m²
of 5 x 5 cm about 0.90 kg / m²

The additional losses due to wasted material on the tiles are 0.05-0.10 kg / m², depending on their surface finish and operation.

Processing time (+ 20 ° C): approx. 1.5 hrs.
Walkability (+ 20 ° C): after approx. 4 hours

Kennzeichnung gemäß Verordnung (EG) Nr. 1272/2008 [CLP]
Gefahrenpiktogramme (CLP):
GHS05
Signalwort (CLP):
Gefahr
Gefährliche Inhaltsstoffe:
Portlandzement
Gefahrenhinweise (CLP):
H315 - Verursacht HautreizungenH318 - Verursacht schwere Augenschäden
Sicherheitshinweise (CLP):
P102 - Darf nicht in die Hände von Kindern gelangenP280 - Augenschutz, Schutzhandschuhe tragenP305+P351+P338 - BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülenP302+P352 - BEI KONTAKT MIT DER HAUT: Mit viel Wasser und Seife waschenP261 - Einatmen von Staub vermeiden.

ARDEX

ARDEX G8S FLEX 1-6

Flex-tile grout, quick

Cement-base

For joint widths of 1-6 mm


For indoor and outdoor


Quick hardening and resilient,

flexible,

Water and dirt repellent,

smooth joint surface,

very good flank adhesion,

highest strength.

With preventive protection against mold.

Suitable for floor and wall heating.


application

For jointing of:
 

•     Porcelain stoneware, stoneware and stoneware tiles
•     glass tiles
•     Natural and concrete stone tiles (insensitive to moisture)
•     Mosaic of glass, porcelain and ceramics

Material need:

with joint width 3 mm, joint depth 5 mm for tiles or medium mosaic

from 60 x 60 cm approx. 0.10 kg / m²

of 60 x 30 cm approx. 0.15 kg / m²

from 30 x 30 cm approx. 0.20 kg / m²

of 15 x 15 cm approx. 0.35 kg / m²

of 10 x 10 cm approx. 0.50 kg / m²

of 5 x 5 cm approx. 1.00 kg / m²


The additional losses due to surplus material on the tiles amount to 0.05 - 0.10 kg / m2 depending on their surface condition and processing method



Processing time (+ 20 ° C): approx. 30 min.
Accessibility (+ 20 ° C): after approx. 90 min.


Package unit:

5kg / 12.5kg paper bag

Kennzeichnung gemäß Verordnung (EG) Nr. 1272/2008 [CLP]
Gefahrenpiktogramme (CLP):
GHS05
Signalwort (CLP):
Gefahr
Gefährliche Inhaltsstoffe:
Portlandzement
Gefahrenhinweise (CLP):
H315 - Verursacht HautreizungenH318 - Verursacht schwere Augenschäden
Sicherheitshinweise (CLP):
P102 - Darf nicht in die Hände von Kindern gelangenP280 - Augenschutz, Schutzhandschuhe tragenP305+P351+P338 - BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülenP302+P352 - BEI KONTAKT MIT DER HAUT: Mit viel Wasser und Seife waschenP261 - Einatmen von Staub vermeiden.

ARDEX

ARDEX G9S Flex 2-15

Flexible tile grout

Product description

 

•     Cementitious Flex Grout Mortar
•     For jointing of porcelain and stoneware tiles,
•     Stoneware and stoneware moisture resistant
•     Natural and concrete stone panels,
•     Glass mosaic,
•     Porcelain and ceramics
•     For joint widths of 2 - 15 mm
•     Water repellent
•     highly deformable
•     Fast hardening and resilient
•     Flexible
•     Good flank adhesion
•     Suitable for floor and wall heating

application


Indoors and outdoors. Floor and wall.

Fur jointing of

- Porcelain stoneware, stoneware and stoneware tiles

- Natural and concrete stone tiles (insensitive to moisture)

- Mosaic of porcelain and ceramics

- clinker, split tiles and fascade bricks

- Glass block walls

Especially for porcelain stoneware, balconies and terraces.

For joint widths of 2-15 mm.

Material needed:

with joint width 6 mm, joint depth 5 mm for tiles.

from 60 x 60 cm approx. 0.20 kg / m²

from 30 x 60 cm approx. 0.30 kg / m²

from 30 x 30 cm approx. 0.40 kg / m²

from 15 x 15 cm approx. 0.60 kg / m²

of 10 x 10 cm approx. 0.90 kg / m²

of 5 x 5 cm approx. 1.80 kg / m²

The additional losses due

excess material on the

tiles vary according to their

Surface texture and

Working method 0.05 - 0.10 kg / m².


processing time

(+20 ° C): approx. 30 min.


walkability

(+20 ° C): after approx. 90 min.

Kennzeichnung gemäß Verordnung (EG) Nr. 1272/2008 [CLP]
Gefahrenpiktogramme (CLP):
GHS05
Signalwort (CLP):
Gefahr
Gefährliche Inhaltsstoffe:
Portlandzement
Gefahrenhinweise (CLP):
H315 - Verursacht HautreizungenH318 - Verursacht schwere Augenschäden
Sicherheitshinweise (CLP):
P102 - Darf nicht in die Hände von Kindern gelangenP280 - Augenschutz, Schutzhandschuhe tragenP305+P351+P338 - BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülenP302+P352 - BEI KONTAKT MIT DER HAUT: Mit viel Wasser und Seife waschen P261 - Einatmen von Staub vermeiden
Zusätzliche Sätze:Inhalt/Behälter gemäß lokalen/regionalen/nationalen/internationalen Vorschriften entsorgen

ARDEX

ARDEX GK

Belastungsfuge

Product description

 

•     Cement-base
•     For jointing of tiles and slabs
•     in workshops, car washes, swimming pools,
•     water tanks, on commercial sites,
•     Stairways, arcades, balconies
•     and terraces
•     For joint widths from 4 mm
•     Resistant to de-icing salt, high-pressure cleaner,
•     high temperatures, mineral oils and common detergents
•     High mechanical strength and abrasion resistance
•     Already walkable after 90 minutes
•     free of cracks

application


Insidoors and outdoors. Floors and walls. For jointing of

- Tiles made of stoneware and porcelain stoneware

- Concrete blocks

- Natural stone slabs (insensitive to moisture)

- split plates and clinker plates

- Fascade bricks and glass blocks

in workshops, car washes, swimming pools, drinking water tanks, on commercial areas, staircases, arcades, balconies and terraces.



Material demand:

with joint width 10 mm,

Joint depth 5 mm

for tiles

of 60 x 60 cm approx. 0.30 kg / m2

from 30 x 60 cm approx. 0.50 kg / m2

from 30 x 30 cm approx. 0.65 kg / m2

of 15 x 15 cm approx. 1.30 kg / m2

of 10 x 10 cm approx. 2.00 kg / m2

The additional losses due

excess material on the

Tiles vary according to their

Surface texture and

processing method 0.05-0.10 kg / m2.


processing time

(+5 ° C to 20 ° C): approx. 30 min.


walkability

(+20 ° C): after approx. 90 min.


Colour:

gray


Package size:

25kg paper bag

ARDEX N23

MICROTEC natural stone and tile adhesive

with ARDURAPID® effect

For wall and floor surfaces indoors.

Non-staining, deformation and blooming-free laying of natural stone, concrete block and cottoplates in thin and medium bed method.

Tiling and laying of stoneware and stone tiles.

Fiber reinforcement.

- Shear stresses are compensated

- Adhesion strengths are improved

- Deformation forces are reduced

Already after about 2 hours walkable / jointable,

adhesive bed thicknesses of 2 - 15 mm,

excellent bond strength,

easy processing,

fast drying.


ARDEX N 23 +

ARDEX E 90 Kunstharzvergütung:

Special adhesives with high formability (S2 according to EN 12002)

and water-repellent properties.


Application:

Indoor. Wall and floor.

Non-staining, blooming and deformation-free tiling of natural stone and natural stone slabs, concrete block and cottoplates in the thin and medium bed method.

Installation and laying of stoneware and stone tiles.

Tiling and laying of tiles and slabs on still shrinking concrete and

Masonry (at least 3 months old).

Plating on screed with integrated heating elements.

Characteristics:

Powders with special cements, fillers, special additives and flexibly operating plastics.

Stirred with water, a supple pasty adhesive mortar results which hardens by hydration with complete crystalline water binding.

Kennzeichnung gemäß Verordnung (EG) Nr. 1272/2008 [CLP]
Gefahrenpiktogramme (CLP):
GHS05
Signalwort (CLP):Gefahr
Gefährliche Inhaltsstoffe:Portlandzement
Gefahrenhinweise (CLP):H315 - Verursacht HautreizungenH318 - Verursacht schwere AugenschädenSicherheitshinweise (CLP):P102 - Darf nicht in die Hände von Kindern gelangenP280 - Augenschutz, Schutzhandschuhe tragenP305+P351+P338 - BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülenP302+P352 - BEI KONTAKT MIT DER HAUT: Mit viel Wasser und Seife waschen

ARDEX N23W

MICROTEC white natural stone and tile adhesive

with ARDURAPID® effect

For wall and floor surfaces indoors.

Staining, deformation and efflorescence-free laying of stone and natural stone, cast stone and cotto slabs in the thin and the middle bed tiling method.

Preparation and laying of stoneware and porcelain stoneware tiles.

Reliability through fiber reinforcement.

- Shear stresses are compensated

- Adhesion strengths are improved

- Deformation forces are reduced

Already after about 2 hours walkable / jointable,

adhesive bed thicknesses of 2 - 15 mm,

excellent bond strength,

easy processing,

fast drying.


ARDEX N 23 W +

ARDEX E 90 resin coating=

Special adhesive with high ductility (S2 according to norm EN 12002)

and water-repellent properties.


Application:

Indoors. Wall and floor.

Staining, efflorescence and deformation-free laying of natural stone and natural stone slabs, cast stone and cotto slabs in thin and medium bed tiling method.

Preparation and installation of stoneware and porcelain stoneware tiles.

Applying and laying tiles and slabs on still shrinking concrete and concrete substrates

Masonry (at least 3 months old).

Claddings on heated screeds.

Preparation and tiling of bright, translucent marble slabs and other natural stone slabs with a translucent character.

type:

Powder with special cements, fillers, special additives and plastics with flexible effect.

When mixed with water, a smooth-pasty adhesive mortar is formed, which hardens by hydration with complete crystalline water binding.

Package sizes:

5kg bucket/25kg bag

Kennzeichnung gemäß Verordnung (EG) Nr. 1272/2008 [CLP]
Gefahrenpiktogramme (CLP):
GHS05
Signalwort (CLP):Gefahr
Gefährliche Inhaltsstoffe:Portlandzement
Gefahrenhinweise (CLP):H315 - Verursacht HautreizungenH318 - Verursacht schwere AugenschädenSicherheitshinweise (CLP):P102 - Darf nicht in die Hände von Kindern gelangenP280 - Augenschutz, Schutzhandschuhe tragenP305+P351+P338 - BEI KONTAKT MIT DEN AUGEN: Einige Minuten lang behutsam mit Wasser spülen. Eventuell vorhandene Kontaktlinsen nach Möglichkeit entfernen. Weiter spülenP302+P352 - BEI KONTAKT MIT DER HAUT: Mit viel Wasser und Seife waschen

ARDEX PU 5

Quick repair resin

Application:

Indoors and outdoors.

For friction locked connections of cracks, dummy joints and outbursts. As an adhesive for nail bars, rails and profiles made of metal, wood, natural and artificial stone and other compatible materials.

As an adhesive for various floor coverings, such as parquet, laminate, etc. The suitability must be ensured before.

Suitable for unheated screeds and heated screeds.


type:

ARDEX PU 5 quick repair resin is supplied in a twin can consisting of component A (resin) and component B (hardener). The attachment contains the shaft connectors supplied.


Mixing ratio:

Component A: 815 g can

Component B: 185 g can


Density:

about 1.5 kg / l

Colour:

Resin: gray

Hardener: beige

Material needs:

The material requirements depend on the width and depth of the joints and cracks. Closing of dummy joints requires approx. 200 g / m.

processing time

(+20 ° C): approx. 10 min.

load-bearing capacity

(+20 ° C): 20 min.

Package unit:

Twin can with 815 g resin / 185 g hardener + shaft connector

ARDEX S28 NEU

MICROTEC Großformatkleber

with ARDURAPID® effect.

For indoor use.

Staining-, deformation- and efflorescence-free laying of natural stones, concrete blocks and cottoplates.

Laying of tiles from stone and fine stoneware.

Perfect for laying large format tiles and slabs on calcium sulphate screeds.

For applying large size and thin tiles to moisture sensitive

Such as e.g. Plasterboards, gypsum plasterboard and wooden subsoils.

Laying of resin-bonded tiles (quartz composites)

Reliable through fiber reinforcement

- Shear stresses are compensated

- Adhesion strengths are improved

- Deformation forces are reduced

For adhesive bed thicknesses of 2 - 15 mm.

After about 4 hours walkable and jointable.

In combination with ARDEX E 90 Kunstharzvergütung, a special adhesive with high formability (S2 according to norm EN 12002) and water-repellent properties is created.


Application:

Indoors. Floor and wall.

Production of a flexible adhesive bed with soft, soft mortar consistency, which allows a fully embedding in the floating method. Staining-, deformation-, and efflorescence-free laying of natural stones, concrete blocks and cottoplates in the thin and medium thick bed method.

Laying of stoneware and fine stone tiles.

Ideally suited for laying large format tiles and slabs on calcium sulphate screeds.

For applying large size and thin tiles on moisture sensitive substrates, e.g. Plasterboards, gypsum plasterboard and wooden subsoils.

Laying of resin-bonded tiles (quartz composites).

Laying of tiles and slabs on still shrinking concrete substrates (at least 3 months old). Plating on screeds with integrated heating elementsi.

type:

Powders with special cements, fillers, special additives and flexibly operating plastics.

Stirred with water, a supple pasty adhesive mortar results which hardens by hydration with complete crystalline water binding.

ARDEX WA

Epoxijoint - grey

•     For jointing of ceramic tiles, slabs, clinker, split tiles and mosaic
•     For adhesion of mosaic of glass and porcelain
•     on wall and floor surfaces
•     resistant to chemicals
•     Highly resilient
•     Easy to joint and wash
•     For joint widths from 2 to 15 mm

Application:

Indoors and outdoors. Wall and floor.

Grouting of ceramic tiles, slabs, clinker tiles, split tiles and mosaic under stress, against the cementitious mortar not sufficiently resilient or unstable.

z. B. in slaughterhouses, dairies, commercial kitchens, breweries, battery rooms, swimming areas and

Spas, shower rooms, baths, sales rooms, sports and leisure buildings and other areas where chemical or high mechanical loads occur.

For joint widths from 2 to 15 mm.


type:

Epoxy resin grout consisting of pasty resin and hardener components.

The 4 kg unit contains 3 kg of resin paste and 1 kg of hardener paste.

ARDEX WA Epoxijoint is waterproof, frost and weather resistant after hardening and has excellent strength and adhesion to tile edges.



Material consumption:

for joints - joint width 3 mm, joint depth 5 mm - are used for tiles or medium mosaic

of 10 x 10 cm approx. 0.45 kg / m2

from 20 x 20 cm approx. 0.25 kg / m2

of 30 x 30 cm approx. 0.30 kg / m2

from 11.5 x 24 cm approx. 0.30 kg / m2

of 5 x 5 cm approx. 0.90 kg / m2

ARDEX WA Epoxifuge is needed.


Losses due to wasted material may be between 0.10 and 0.20 kg / m2, depending on the type of tile and the method of processing.


processing time

(+20 ° C): approx. 80 min.


Laying time:

(+20 ° C): approx. 80 min.


Correction time

(+20 ° C): approx. 80 min.


walkability

(+20 ° C): after sufficient hardening, after approx. 12 hours


containers:

Bucket of 3 kg ARDEX WA base paste

Can with 1kg ARDEX WA hardener
   

ARDEX WA

Epoxi tile adhesive

•     Epoxy resin adhesive
•     Matches the R2 requirements of norm EN 12004
•     For preparing and laying ceramic tiles, slabs, clinker tiles, split tiles and mosaics
•     resistant to chemicals
•     Highly resilient
•     Easy to process
•     Good stability

Application:

Indoors and outdoors. Wall and floor.

Preparation and laying of ceramic tiles, slabs, clinker tiles, split tiles and mosaic under stress, against which cementitious mortars are not sufficiently resilient or unstable. z. As in slaughterhouses, dairies, commercial kitchens, breweries, battery rooms, swimming pools and spas and other areas where chemical or high mechanical loads occur.


type:

Gray epoxy resin adhesive mortar consisting of pasty resin and hardener components.

The 4 kg unit contains 3 kg of base resin paste and 1 kg of hardener paste.

ARDEX WA Epoxy Adhesive is water resistant, frost and weather resistant after hardening, has excellent strength and is nearly insoluble on any suitable substrate such as concrete, cement screeds, cement plaster, terrazzo saws and old tiles.


Chemical resistance according to AQS:

Resistant to:

sewage *

Ammonia, conc.

Calcium hydroxide, saturated

Chromic acid 5%

Developer Solution (Photogr.)

ethylene glycol

feces

Fixing solution (Photogr.)

Hydrofluoric acid 1%

Formalin solution 3%

glycerin

household cleaners

heating oil

Potash, saturated

Automotive gasoline

seawater

Methyl alcohol <50%

Lactic acid 10%

Moorwasser

Sodium hydroxide, saturated

vegetable fats

Phosphoric acid <50%

Nitric acid <10%

Hydrochloric acid <36%

Sulfuric acid <80%

brine

animal fat

Hydrogen peroxide <10%

Tartaric acid, saturated

Citric acid, saturated

sugar solution

* In the case of industrial waste water suitability is to be checked in individual cases!


Temporary resistant to:

Formic acid 1%

5% acetic acid

Ethyl alcohol, conc.

Hydrofluoric acid 5%

Lactic acid 20%

Nitric acid <40%


Not resistant to:

acetone

3% formic acid

Butanone (MEK)

chloroform

Acetic acid> 10%

ethyl acetate

Hydrofluoric acid> 5%

methylene chloride

Lactic acid> 20%

Nitric acid, conc.


Mixing ratio:

is specified by the containersizes


weight of the fresh mortar:

about 1.5 kg / l


Material needed:

for application on a smooth surface

about 1.5 kg / m2

notched trowel with 3 x 3 x 3 mm,

approx. 2.7 kg / m2

notched trowel with 6 x 6 x 6 mm,

approx. 3.7 kg / m2

notched trowel with 8 x 8 x 8 mm


containers:

Bucket of 3 kg ARDEX WA base paste

can with 1kg ARDEX WA hardener